Versalift VST-40-MHI equipped as follows:

-          Insulated

-          45 ft working height

-          Platform capacity of 400 lbs

-          Side mounted closed heavy-duty one-step 24” X 30” X 42” fiberglass platform including platform liner and vinyl cover

-          VERSALIFT TruGuard™ dielectric isolating system with right hand single-stick control. All control handles are isolated and tested per ANSI 92.2. The high resistive dielectric system is protected from direct environmental and job related contamination. TruGuard™ technology incorporates the use of full hydraulic controls with durable metal handles and linkages

-          Hydraulic dual arm articulating jib pole and winch package for up to 1,000 lbs. capacity, including insulated jib pole

-          Side mounted telescopic upper boom allows low stowing of platform. Fiberglass inner boom and patented ELECTROGARD provide insulation gap of 46” fully retracted meeting ANSI A92.2 requirements for Category C 46KV and below

-          360° continuous rotation including slip rings

-          Individual full pressure controls at the turret actuate all boom functions and is equipped with a selector valve to override upper controls

-          Six GPM (22.7 lpm) open center hydraulic system with a 3000 psi (210 kg/cm²) operating pressure

-          Chassis insulating system (fiberglass lower boom insert) providing 12” insulation gap and including accommodations to bridge insulation gap for testing per ANSI 92.2

-          ELECTROGARD and inner boom finished with white urethane paint over a white gel coat

-          Integral reservoir with a 17-gallon (64.4 l) capacity and dual sight gauges

-          Non-lube bearings used throughout

-          Automatic throttle control

-          12 Volt DC backup pump providing power to all boom functions

-          Sub frame mounted main A-frame outriggers with pivot feet, two control valves, and a selector valve

-          Outrigger boom interlock system for main outriggers

-          Auto boom latch for mounting on outer boom ELECTROGARD. The rotary auto boom latch works off the lift hydraulic pressure to open and close

-          Safety harness and lanyard

-          Standard white urethane paint

Brand FX body equipped as follows:

-          132” X 42” X 94” service body

-          30 inch aluminum tread plate platform extension

-          BFX LED lighting package installed in tail shelf

-          Cable access step at rear and side access

-          Two (2) stainless steel grab handles at side access and two (2) aluminum grab rails at rear tail shelf

-          Wheel chock storage and outrigger pad holders

-          Push/pull rod lock system

-          42” High Street side compartments as follows

o   1st Vertical: Two (2) adjustable shelves with dividers with outrigger cutout

o   2nd Vertical: Two (2) adjustable shelves with dividers

o   Horizontal: One (1) removable shelf with dividers

o   Rear Vertical: Two (2) adjustable shelves with dividers

-          42” High Curbside compartments as follows

o   1st Vertical: Two (2) adjustable shelves with dividers with outrigger cutout

o   2nd Vertical: Grip strut access steps to bed area with removable plastic tail board

o   Horizontal: One (1) adjustable shelf with dividers

o   Rear Vertical: Five (5) fixed material hooks 1-3-1

MOUNTED ON:

2022 Chevy 5500 4x4 equipped as follows:

-          19,500 lbs GVWR

-          6.6L Duramax V8 Turbo diesel engine

-          6-speed Allison A1700RDS automatic transmission

-          Front axle – 7,500 lb, multi-leaf suspension

-          Rear axle – 15,500 lb multi-leaf suspension

-          110-volt AC power outlet

-          1300 cold-cranking amps heavy-duty dual batteries

-          Air conditioning

-          Engine block heater

-          225/70Rx19.5G all traction tires.

-          AM/FM stereo with Bluetooth USB port, and auxiliary jack

-          40/20/40 split vinyl bench seat

-          Back up camera

-          Transfer case skid plate shield

-          Painted Summit White